Product Description:
Model: Horizontal, four Tie Rods, control system of oil pressure, PLC for electric power, semi-automatic control, easily operated, automatic die slide and billet loader into the container.
Features: This machine is equipped with pump of variable capacity which can automatically control the capacity of oil by the variation of pressure. Electric power consumption is low and the temperature of oil is not easy to rise. Speed control is also available. Therefore, the efficiency of the machine is extremely high. Our special design is Double Shears for cutting billet: square shears which are
Product Description:
This equipment consists of initial table, conveyor, cooling table, carriage, stretcher, storage table, product sawing table, and treating cart. 1.According to extruding speed, the electric device of heat resistance roller sleeves can adjust the speed with motor of convertible frequency which a device of convertible control is attached. 2.Cooling table is design of heat resistance. Therefore, products are not easily spoilable. 3.Billet loader is driven by gear of eccentric motor to move up and down and is conveyed to cooling table by belt gear. 4.Stretcher is made of steel. It can apply to
Product Description:
The puller produces various special industrial aluminum products in co-ordination with 420 US Ton~4400 US TON extrusion press. It is easy to operate and retrenches manpower. This machine is made of steel which can fix length with front platen saw table. This machine uses a D.C. motor to drive the gears; and an A.C. motor to drives the jaw. Sprocket automatically clips aluminum profiles with chains. According to the extruding speed of extrusion press, puller can adjust the speed and twisting force of clamp appropriately. Therefore, the accuracy of aluminum products can be attained. Re
Product Description:
ntroduction: This machine is made of steel. The head of jaw is driven by oil pressure. The tail of jaw can be adjusted according to the length of the aluminum profile. 1.Pulling Force: 68UST, 35kg/cm²~90UST, 140kg/ cm?
2.Straightening length: 3M-50M 3.Straightening stroke: 700mm~1200MM 4.Opening of jaw: 90mm~240mm
1.The method for cutting billets is cutting from up to down. 2.This equipment has the function of aluminum billet saw and operates in coordination with LPG direct fire billet heating furnace. You can adjust the length of billet quickly and do all the processes at one time. Thus, it can save manpower cost for cutting aluminum billet. 3.The rest aluminum billet can be connected to next billet so it can retrench loss of 5mm billet each time. Thus, there will be no waste material. 4.You can change different quality of aluminum billets which are the same size as
Product Description:
Introduction: Type: Tunnel Continuous type Method: Both sides direct fire heating Advantage: Temperature rising speed is fast. It is less fuel, equal temperature, stable, exact temperature. It fits in with fewer amount and multiple demands nowadays. Whole systems are automatic control. Charging from up and discharging from down, temperature inspection, and fire control are controlled by USA ALLEL BRADLEY PLC and HML PANEL.
Product Description:
Introduction: 1. This equipment can put a lot of billets on the storage table and continuously cut billets. 2. This equipment uses PLC electricity automatic control and it is easy to operate. 3. Cooling cutting oil automatically supply and stop. 4. It can depend on the billet length and material to adjust the cutting length and speed. 5. Cutting diameter of Billet: £p3¡¨~£p8¡¨;£p3Ѕ¡¨~£p10¡¨ 6. Cutting one cycle time: £p3¡¨~£p6¡¨ about 12 seconds; £p7¡¨~£p10¡¨ about 30 seconds
Product Description:
Automatic Handling System- Flat Transfer Type
Description: This equipment consists of Initial table, Roller Sleeve Raise/lower conveyer (Adjustable speed), Run Out transfer table (Flat Transfer Type), Cooling table (Flat Transfer Type), Stretcher, Stretcher Transfer table (Flat Transfer Type), Storage table (Flat Transfer Type), Sawing Transfer Table (Roller Sleeve Type), Product sawing table, Length gauge table, automatic control.
Feature: It is used for big machines such as 2200UST ~ 2750UST. Because big profiles are heavier and there is no belt slippery problem for Flat transfer equ
Product Description:
Vertical Automatic Finished Product Saw Description: Vertical Automatic Finished Product Vertical Automatic Finished Product Saw A. Firm structure. Small shaking. High precision for cutting B. When adjusting dimension, there is orientation device with digital display. C. Server motor drive for charging. D. Cutting dimension: Height: 120mm Weight: 120mm Length: 6mm to 400mm E. After finishing cutting profiles, jaws on both right and left sides open automatically.
